LD Systems IPA424T 4-Channel Hybrid DSP Amplifier 4x 240W
Introducing the LD Systems IPA424T 4-Channel Hybrid DSP Amplifier 4x 240W professional amplifier. LD systems have included Four Channels to operate at 4x 240 Watts. All the outputs on the IPA424T are high-quality toroidal core transformers and operate at 70V/100V.
These transformers are perfect for use with the LD Systems DQOR 3T, DQOR 5T, DQOR 8T speakers. While the low impedance 4-Ohm outputs with the transformer-less operation will guarantee you the highest possible audio quality.
The IPA424T comes packed with versatile functions; including a parametric EQ with a matching speaker library, dynamic tools, a matrix mixer, priority source selection, and delay. Despite this range of functions, the IPA Series power amps are easy to operate. Important functions such as signal, limit, protection, and bridge mode are easily visible via the LEDs on the front panel.
On the back of your IPA424T, you will find a few future-proofing connections. For example, the Ethernet card offers comprehensive configurations and management via software. As the Dante card offers audio networking capabilities to a wide range of Dante-enabled devices. As a result, you can integrate the IPA424T into the Dante network in order to resolve more complex tasks.
Scalability and future-proofing are the biggest advantages of the IPA Series. Its energy efficiency is also ideal thanks to the Class-D technology and switchable auto standby.
In conclusion, good sound belongs everywhere. In the hotel lobby, in conference rooms, in schools, and in houses of worship. Demands are constantly increasing, not only in terms of quality but also in terms of flexibility. Permanently installed and still flexible? This apparent contradiction can be resolved by the IPA Series DSP-based installation amplifiers.
The IPA412T variant with 4 x 120 watts is available for smaller installations.
Width: 483 mm
Height: 44.5 mm
Depth: 425 mm
Weight: 11,36 kg
Product type: Amplifier
Type: Installation power amplifier
Audio Channels: 4
Output Circuitry: Class D
Operating voltage: Wide Range SMPS with PFC (power factor control)
Mains connector: IEC socket
Auto-Standby Power: Yes. Switchable (On-Off)
Time to Auto-standby: 20 Min with no audio input signal
Indicators: Front Panel: “PROT”, “LIMIT”, “SIG”, “BRIDGE” and Mute Symbol LED´s. Power On/ Standby LED, Rear Panel: 4x Input Clip LED´s, Remote Lock LED (Red)
Controls Front panel: On/off switch, standby
Controls Element Back Panel: “BRG“ (Bridge), “PAR“ (Parallel), “ST“ (Stereo), Amplifier Channel Mode, Low-Z and High-Z switches (paired), Output Volume potentiometers, Preset A and B switches, Remote Lock, Remote ON/OFF, Remote-Mode, Standby On/Off
Inputs: 4x Balanced Line Inputs, Remote Bus Audio Input
Input connectors: 6-pin Terminal Block Pitch 3.81mm, Remote IN/OUT RJ45, Service connection Micro USB type B
Expansion Slot: For optional Ethernet, or Ethernet + Dante cards
Cooling: front to rear/side airflow, Passive + 2-zone temperature-controlled active cooling
Operating voltage: 100 V AC – 240 V AC, 50 – 60 Hz
Fuse: T10AL 250 V
Inrush Current Power OFF-Standby: 2.8 A
Inrush Current Standby-ON: 0.5 A
Power Consumption @ Standby: 0.9 W
Power Consumption @ idle mode: 30 W
Power Consumption @ full load: 1000 W
Operating temperature: 0 °C – 40 °C; (max 60% relative humidity)
Amplifier Output Specifications, all outputs are driven and loaded
Rated ouput power (1kHz @ 4 Ohms): 4 x 240 W (1.5 seconds sine burst)
Rated ouput power (1kHz @ 8 Ohms): 4 x 120 W (1,5 Seconds Sine Burst)
Rated ouput power (1kHz @ 16 Ohms): 4 x 60 W (1.5 Seconds Sine Burst)
Rated ouput power (1kHz @ 8 Ohms, bridged): 2 x 490W (1.5 Seconds Sine Burst)
Protection circuits: Audio Limiter, DC, HF Protect, HPF (High-Z), short circuit, temperature, thermal overload
Minimum load impedance per channel: 4 ohms Single-Ended, 8 ohms Bridge
Nominal input sensitivity: +5 dBu (Sine 1 kHz, Gain max)
THD + N: < 0,03 % (Low-Z SPK OUT, +18 dBu, 20 Hz – 20 kHz)
Frequency response: 18 Hz – 22 kHz (Low-Z OUT, -3 dB), 50 Hz – 23 kHz (High-Z OUT, -3 dB)
System Latency: 6.2 ms
AD/DA converter resolution: 24 bit
AD/DA converter sampling rate: 48 kHz